Exterior Car Parts

Thanks for visiting our site!
Bracket Ford
Checkout Ebay Auctions For The Cheapest Prices

Here are some more information for Bracket Ford:

1939 Ford Four Door Deluxe Project Part 2

What do we need to do to get this motor in?

Now its easy to assume that the Ford engine mounts do not match up to the Chevys. We found our Hot Rods engine and trans mounts  at Chasssis Engineering. They come with hardware and simple instructions. Our Ford frame is "X" shaped and has a bracket that strengthens the "X" where the frame intersects. The original needed to be drilled out and refitted with the conversion piece.

Get it together

Our conversion pieces lined up well with the original holes. We needed to enlarge some holes to install bolts, and drill some new holes,  but all in all, its not too bad, just a bit tougher with the body on the car. The lower suspension arms need to be mounted to our center support differently and retrofit brackets are available to do this. The engine mounts are installed via a diagram. Measure twice and drill once. This is very easily done.

Mock it up

We had access to a junk engine and trans for fit. If this is not available to you, do not worry. Just use what you have and be a bit more careful. Our motor and trans fit perfectly with no surprises and looks great. Check all clearances, especially firewall. Chevys have the distributor at the rear so make sure there are no firewall clearance issues. Exhaust clearances are great and steering column will not be in the way of anything.

How does it look?

Our Chevy engine/trans combo weigh about the same as the flathead, so ride height is pretty much the same. The drivetrain dimensions are very similar, but remember that the radiator configuration is different with a Chevy. There should be no height issues as the Ford's hood is very stout and tall.

Final preparation

Once mock engine and trans are removed, we took the time to sand down the brush painted engine compartment. We did some minor bodywork around welded holes and small dents. Again, it all depends on what you want your finished product to look like. Use a good wax and grease remover for a final wipe down. We chose to put a coat of primer prior to applying two coats of a satin black finish. This will allow the focus to be on the engine, and also keeps with the factory look.

Engine and trans paint

Since we are painting, now is the perfect time to paint your engine and trans. Again, we chose the factory lead sled look and painted the engine a dark green while leaving the trans a satin black as well. Our motor was brand new so we took the time to clean and prep prior to painting. Same with the trans. If you do not have a paint booth, allow a good day or two for the paint to dry sufficiently. Dont rush this part as it will just ruin the final product you worked so hard to achieve.

Next time: we assemble the engine and trans and in it goes!

Come visit us at http://www.ratrodauthority.com.com for ideas, parts, vehicles and anything to do with Rat Rods, Muscle Cars, and Hot Rods.

About the Author

Started by Art Tupaczewski, his experience in the auto body industry lead him to devise a way to find
that "specialty part" for your car quickly, easily, and cost effectively. Whether just starting
out, or a seasoned veteran, http://www.ratrodauthority.com has what you need.

After analyzing the marketplace, Art figured out an efficient way to get what you need fast and correct
from the comfort of your own home. His website is the most user friendly and is designed to tell you exactly
what you need to know so you can get back to your project. No guesswork and up to the date
products allow you to move at a rapid rate and checkout quickly.

Whether its an exhaust for your lead sled, wheels for your jalopy, or tires for your Chevelle or Camaro,
you can rest assured knowing that you found the only place to shop for your car.

So always remember, from rust buckets to hot rods, the rat rod authority is available 24 hours a day, 7

help if you can. i need a pic.of the bracket placement on a 1972 ford or Lincoln?

i'm restoring a lincoln continetal

have you went to the local library and looked in a Chilton's Manuel or you could buy one for about 50$ from an auto parts store

Familiar faces return to victory lane at Maple Grove
THE PHOENIX STAFF REPORT sports@phoenixvillenews.com

Thanks for visiting!